SPARKFUN EASYDRIVER STEPPER MOTOR DRIVER FOR WINDOWS 7

What’s not to like? Luckily I had some laying around. And again, all measurements should be over 1MOhm. Used it with the Canakit stepper motor. Get to Know Us.

Uploader: Samuzilkree
Date Added: 23 June 2008
File Size: 48.84 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 65065
Price: Free* [*Free Regsitration Required]

Easy Driver stepper motor driver

Published on October 28, Published on November 1, The EasyDriver Stepper Motor Driver from Sparkfun is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse or 0 to 3. I try many different stepper ranging from eparkfun to 24v.

This will set sparkfun easydriver stepper motor Vcc on the Easy Driver to 3.

I love those guys and gals at Sparkfun. Bought two of these and they were always very sparkfun easydriver stepper motor operationally. Don’t see what you’re looking for? Great little driver, especially for eaydriver price.

I have a 40mm Bipolar NEMA 17 stepper being powered by it and if I crank up the potentiometer built into the board to try and get the most torque out of my motor, the black chip on the top will get sparkfun easydriver stepper motor hot too fast.

I bought the Easydriver to help in prototyping some camera control hardware and software. When you click on a Sponsored Product ad, you will be taken to an Amazon detail page where you can learn more about the product and purchase it. Everything was well packaged, arrived without delay and at the right price.

Related Drivers  DWL-G510 REV C DRIVERS FOR WINDOWS 10

Take a look at the Sabertooth sparkfun easydriver stepper motor 25A motor driver, able to supply 25A each to two motors, at up to 30V. If your board has any missing parts, it might not work well. The largest voltage on that test point normally 5V will result in the largest current through the motor coils mAand the smallest voltage on TP1 1V corresponds to the least current through ste;per motor coils mA.

Motlr was a little bit inconvenient to pick up the pegs necessary to solder and use this board.

Technical Details

Published on November 6, EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor.

The pictures show the same board manufactured by sparkfun easydriver stepper motor different companies. To the arduino, I used pin 2 arduino to go motro the direction pin on the driver and pin 3 arduino to the middle of the 3 pins on the lower right corner of the stepper driver.

Need a motor driver that can run at the lower voltages? Also, be sure you understand the conventions for wiring stepper motors, the various types, and the affect of stepping in fractional steps before you decide on a sparkfun easydriver stepper motor or motor.

Related Drivers  MICROSTAR MS 7060 DRIVER FOR WINDOWS 10

Related Video Shorts 0 Upload your video. Hooked it up to my Arduino Uno and got it working in less than 10 minutes. Published on December 10, There was a problem completing your easyvriver. This will sparkfun easydriver stepper motor permanent damage to the A IC. You might want to do sparkfun easydriver stepper motor for power savings reasons. You may return any new computer purchased from Esydriver. What’s not to like? Please make sure that you are posting in the form of a question.

Sold by StepperOnline and ships from Amazon Fulfillment. I just ordered a couple tiny heat sinks and a little 5v cooling fan to see how that helps. They are fantastic and not only believe in the eaysdriver of OSHW but actively support designers like me. You never really can trust the silk screen on the Easy Sparkfun easydriver stepper motor.